点击图片查看原图
英国GRIMM格林进口锅炉给水泵概述：
进口锅炉给水泵系卧式单级多级分段式离心泵，可供输送清水或物理化学性质类似于清水的液体，适用于中、低压锅炉或次高压锅炉给水，也适用于工厂或城市高压给排水。输送介质温度为-20℃～105℃，进口允许压力小于0.6MPa。
进口锅炉给水泵采用了英国格林推荐使用的高效节能产品的水力模型。具有效率高、性能范围广、运转安全和平稳、噪音低、寿命长、安装维修方便等优点。
英国GRIMM格林进口锅炉给水泵结构特点：
1、泵的进、出水口均为垂直向上，通过拉紧螺栓将泵的进水段、中段、出水段、轴承体等泵壳体部分联结成一体。根据泵的扬程选择泵的级数。
2、泵的转子部分主要由轴及安装在轴上的叶轮、轴套、平衡盘等零件组成，其中叶轮的数量根据泵的级数而定。轴上零件用平键和轴螺母紧固使之与轴联为一体。整个转子由两端滚动轴承或滑动轴承支承。轴承按型号不同而定，均不承受轴向力，其轴向力由平衡盘平衡。泵在运行中允许转子在泵壳中轴向游动，不能采用向心球 轴承。滚动轴承用油脂润滑，滑动轴承用稀油润滑中，并用油环进行自润滑，循环水冷却。
3、泵的进水段、中段、出水段之间的密封均采用二硫化钼润滑脂密封，转子部分与固定部分之间装有密封环、导叶套等进行密封，当密封环和导叶套的磨损程度己影响泵的工作性能时应予更换。
4、轴的密封形式有机械密封和填料密封两种。泵采用填料密封时，填料环的位置安放要正确，填料的松紧程度必须适当，以液体能一滴一滴渗出为宜。泵各种密封元件装在密封箱内，箱内要通入一定的压力的水，起水封、水冷或水润滑作用。在轴封处装有可更换的轴套，保护泵轴。
5、高压泵一般采用滑动轴承、稀油润滑结构，可采用滑动轴承、稀油润滑，也可采用滚动轴承、干油润滑结构，其余型号均采用滚动轴承、干油润滑结构。中、低压泵的主要零件材料一般采用优质铸铁，次高压泵主要零件采用铸钢或不锈钢。该系列泵通过弹性联轴器由原电机直接驱动，从原电机方向看，泵为顺时针方向旋转。
英国GRIMM格林进口锅炉给水泵特点：
1、水力模型先进，效率高，性能范围广。
2、泵运行平稳，噪音低。
3、轴封采用软填料密封或机械密封，密封安全可靠、结构简单，维修方便快捷。
4、轴为全封结构，确保了不与介质接触，不锈蚀，使用寿命长。
英国GRIMM格林进口锅炉给水泵主要参数：
流 量：3.75-500m3/h
扬 程：55-680m
口 径：50-200mm
转 速：1450-2950r/min
功 率：2.2-400kw
温度范围：≤105℃
工作压力：≤3.0Mpa
材 质：铸铁、铸钢、不锈钢
英国GRIMM格林进口锅炉给水泵适用范围：
适用于工业和城市给排水、高层建筑增压供水，园林喷灌、消防增压、远距离送水、采暖、浴室等冷暖水循环增压及设备配套等，尤其适用于小型锅炉给水。
UK GRIMM imported boiler feed pump summary:
imported boiler feedwater pump system for Horizontal single-stage multistage centrifugal pump, can be used to transport water or similar physical and chemical properties of liquid water, suitable for medium and low pressure boiler or pressure boiler feedwater, also applies to the factory or city high pressure water supply and drainage. The medium temperature is -20 ~ 105 DEG C, and the inlet pressure is less than 0.6MPa.
The imported boiler feed pump adopts the hydraulic model of efficient energy-saving products recommended by Green. The utility model has the advantages of high efficiency, wide performance range, safe and steady operation, low noise, long service life, convenient installation and maintenance, etc..
UK GRIMM imported boiler feed pump structure characteristics:
1.The pump inlet and outlet are vertical upward, through the tension bolt will pump the water inlet, middle section, the water outlet section, the bearing body and so on pump shell part is connected as a whole. Select the series of pumps according to the pump lift.
2.The rotor part of the pump mainly by the shaft and the impeller installed on the shaft, shaft sleeve, balance plate and other parts, in which the number of impeller according to the pump series and fixed. The shaft parts are fastened by flat keys and shaft nuts so as to be connected with the shaft as a whole. The whole rotor is supported by rolling bearings or sliding bearings at both ends. The bearings are different according to the model, and they do not bear axial force. The axial force of the bearings is balanced by the balance disc. In operation, the rotor is allowed to swim axially in the pump housing, and radial ball bearings cannot be used. The rolling bearings are lubricated with grease. The sliding bearings are lubricated by thin oil, and lubricated by oil rings. The circulating water is cooled.
3.Pump seal between the water inlet section, the middle section of the water are used MoS2 grease seal, a sealing ring, a guide vane sleeve for sealing is arranged between the rotor part and the fixed part, when the sealing ring and the guide vane sleeve wear should be replaced so affect the pump performance when.
4.The shaft seal in the form of mechanical seal and packing seal two. Pump packing seal, the packing ring position should be placed properly, the tightness of the packing must be appropriate, with a drop of liquid can be a drop of appropriate. All kinds of sealing elements are installed in the sealed box. The water in the box must pass through a certain pressure, and the water seal, water cooling or water lubrication can be used. A replaceable shaft sleeve is arranged at the shaft seal to protect the pump shaft.
5.High pressure pumps generally use the oil lubrication structure, sliding bearing, the sliding bearing, oil lubrication, also can use rolling bearing, grease lubrication structure, the other models are the rolling bearing, grease lubrication structure. The main parts of medium and low pressure pumps are made of high quality cast iron, and the main parts of secondary pumps are made of cast steel or stainless steel. The series pump is driven directly by the original motor through an elastic coupling, and the pump rotates clockwise in the direction of the original motor.
UK GRIMM imported boiler feed pump characteristic:
1.Hydraulic model advanced, high efficiency, wide range of performance.
2.The pump runs smoothly and the noise is low.
3.Tthe shaft seal adopts soft packing seal or mechanical seal, the sealing is safe and reliable, the structure is simple, and the maintenance is convenient and quick.
4.The shaft is a full seal structure, to ensure that no contact with the media, no rust, long service life.
UK GRIMM imported boiler feed pump technical parameter:
Flow rate: 3.75-500m3/h
Lift: 55-680m
Caliber: 50-200mm
Speed: 1450-2950r/min
Power: 2.2-400kw
Temperature range: less than or equal to 105 DEG C
Working pressure: 3.0Mpa
Material: cast iron, stainless steel
UK GRIMM imported boiler feed pump scope of application:
Suitable for the industry and the city water supply and drainage, high-rise building pressurized water, garden irrigation, fire booster, long-distance water, heating, bathroom pressurization of cold and hot water circulation equipment, especially suitable for boiler.